DC Withstand Testing of Insulators: Test Methods, Procedures and Equipment Selection

Content by SUTE technical team — high-voltage test equipment manufacturer.

Insulators used in high-voltage power systems must maintain reliable electrical insulation under demanding operating conditions. For manufacturers, verifying this performance before a product leaves the factory is an important part of quality control and product development.

A DC withstand voltage test is one of the electrical tests that may be specified for insulators, particularly those designed for DC applications or products requiring DC dielectric verification.

Unlike an AC withstand test, a DC test applies a continuous high voltage for a specified period. During the test, engineers monitor the applied voltage and leakage current to evaluate the insulation condition.

This article explains how DC withstand testing works, how it is performed and what to consider when selecting a high-voltage DC test system.

1. Why Perform a DC Withstand Test on Insulators?

The main purpose of a DC withstand test is to verify whether an insulator can withstand a specified direct voltage without electrical breakdown or other unacceptable insulation failure.

During manufacturing and product development, this test can help engineers identify potential insulation weaknesses and verify that the product meets its specified electrical performance requirements.

DC withstand testing may be required for:

  • Insulators designed for HVDC transmission systems.

  • Ceramic and glass insulators where DC dielectric testing is specified.

  • Composite insulators intended for DC applications.

  • Research and development projects involving DC insulation performance.

The test requirements are not identical for every insulator. Material, construction, rated voltage and application all influence the test conditions.

For this reason, the applicable product standard and technical specification should always determine whether a DC withstand test is required.

2. How Does a DC Withstand Voltage Test Work?

The basic principle is straightforward: a controlled DC high voltage is applied across the insulation system of the test object and maintained for a specified duration.

A high-voltage DC generator converts its input power into a regulated high-voltage DC output. The output is connected to the insulator through the designated test electrodes or conductive fittings.

As the voltage increases, the test team monitors the applied voltage and leakage current.

A stable test voltage with no unacceptable current increase or insulation breakdown generally indicates that the test object has withstood the applied electrical stress. Final acceptance, however, must follow the relevant test specification.

Several parameters are important during the test:

  • Test voltage: The specified DC voltage applied to the insulator.

  • Test duration: The period for which the specified voltage is maintained.

  • Leakage current: The current flowing through or over the insulation system.

  • Polarity: Positive or negative DC voltage, depending on the test requirement.

  • Test environment: Temperature, humidity and surface conditions that may influence the results.

One important point is that DC leakage current can include both capacitive charging current and conduction current. Therefore, readings should be evaluated with consideration of the charging period and the test procedure, rather than treating every initial current change as an insulation defect.

3. DC Withstand Test Procedure

A reliable DC withstand test depends not only on the output capability of the generator but also on proper test preparation and connections.

A typical laboratory procedure includes the following steps.

Step 1: Inspect the test object

Check the insulator for visible cracks, contamination, moisture or mechanical damage. Confirm the product type and test requirements before connecting the equipment.

Step 2: Set up the test circuit

Connect the high-voltage DC output to the specified electrode or fitting. Establish the required grounding and measuring connections according to the test arrangement.

The test area should be properly isolated, with appropriate safety clearances and protective interlocks.

Step 3: Increase the DC voltage

Raise the output voltage in a controlled manner until the specified test level is reached. The voltage application rate should follow the relevant test procedure.

Step 4: Maintain the test voltage

Hold the specified voltage for the required duration while monitoring leakage current and observing the test object for abnormal discharge or breakdown.

Step 5: Reduce voltage and discharge

After the test, reduce the output voltage, disconnect the supply as required and safely discharge the test object. High-voltage DC systems can retain residual charge, so proper discharge and grounding are essential before handling the test object.

Step 6: Record and evaluate the results

Record the test voltage, duration, polarity, leakage current and any abnormal observations. Determine whether the insulator meets the specified acceptance criteria.

4. What Does Leakage Current Tell Us?

Leakage current is an important parameter in DC insulation testing.

When DC voltage is first applied, the measured current usually includes a charging component. As the test continues, this component decreases and the current increasingly reflects conduction through the insulation and along its surface.

A relatively stable leakage current may indicate normal insulation behaviour under the specified conditions.

However, an unexpected increase in current, unstable readings or a sudden current change may indicate surface leakage, contamination, moisture or possible insulation deterioration.

Engineers should not judge insulation quality based on one current reading alone. The voltage level, elapsed time, test environment and insulator construction must all be considered.

5. How to Select a High-Voltage DC Generator for Insulator Testing

Choosing a suitable DC test system requires more than looking at its maximum output voltage. The generator must match the electrical characteristics of the test object and the requirements of the test procedure.

The following factors deserve attention.

Selection factor

What to consider

Output voltage

Must cover the specified test voltage

Output current

Suitable for the expected test load and leakage current

Voltage regulation

Maintains a stable output during testing

Measurement accuracy

Supports reliable voltage and current monitoring

Ripple performance

Appropriate for the required DC test conditions

Protection functions

Overcurrent, overvoltage and other necessary safeguards

Operating arrangement

Suitable for the laboratory layout and test object

For insulator testing, the required output voltage, current capacity and measurement accuracy should be determined from the actual test specification.

A properly selected high-voltage DC generator helps laboratories conduct repeatable tests and monitor insulation performance more effectively.

6. SUTE High-Voltage DC Generator for Insulation Testing

SUTE's High-Voltage DC Generator is designed for high-voltage DC testing applications.


High-Voltage DC Generator

Suitable for specified DC withstand tests on insulators and other high-voltage electrical equipment.

View Product Details

For insulator manufacturers and high-voltage testing laboratories, the system can be considered for DC dielectric testing according to the required test voltage, duration and measurement conditions.

The equipment configuration should be selected based on the test object's electrical characteristics and the applicable testing requirements.

If you are planning a DC withstand test for insulators, providing the insulator type, rated voltage and required test voltage will help determine a suitable equipment configuration.

7. Relevant Standards for Insulator DC Testing

The applicable standards depend on the type of insulator and its intended application.

The following standards provide useful technical references:

Standard

Scope and relevance

IEC 60060-1:2025

General requirements for high-voltage dielectric tests, including DC voltage testing

IEC 60383-1:2023

Ceramic and glass insulator units for AC overhead lines and certain DC traction applications

IEC 61109:2025

Composite suspension and tension insulators for AC and DC overhead line applications

DL/T 626—2024

Inspection procedures for deteriorated suspension insulators

IEC 60060-1 provides the general framework for high-voltage dielectric testing, including DC test techniques. IEC 60383-1 and IEC 61109 address specific insulator product families and their corresponding test requirements.

DL/T 626—2024 focuses on detecting deterioration in suspension insulators used in AC and DC power systems. It is relevant to in-service inspection, rather than a standalone factory DC withstand test standard.

Manufacturers should refer to the applicable product standard and its specified test clauses when determining the required DC test voltage, duration and acceptance criteria.

Frequently Asked Questions

Is a DC withstand test suitable for all types of insulators?

Not necessarily. DC withstand testing is mainly used when required by the product standard, application or project specification. The test method should match the intended operating conditions of the insulator.

What is the difference between AC and DC withstand testing?

AC testing applies alternating voltage, while DC testing applies a constant-polarity voltage. The two methods produce different electric field and charge distribution conditions within insulation materials. Their results are not directly interchangeable.

Why should leakage current be monitored during a DC withstand test?

Leakage current provides information about the electrical behaviour of the insulation under DC stress. Unexpected changes may indicate surface leakage or insulation problems and should be investigated.

What information is needed to select a high-voltage DC generator?

The insulator type, rated voltage, required DC test voltage, test duration, expected leakage current and applicable standard are the main starting points for equipment selection.